|
| |
MCB
Wireless remote master control board WITH TEXT & TEXT TO VOICE
FACILITY

|
- POCSAG or Flex
- VHF or UHF
The MCB Multi-purpose Master Control Board is a
breakthrough an intelligent remote control and alerting
receiver complete with four on board & 4 off board relays while
simultaneously delivering text through a serial port to be displayed
at LED signs and text to voice through audio jack to external horn
speakers.
Relays can be controlled by
Numeric, Alphanumeric messages as well as with capcodes
|
PSR3000 SERIAL RECEIVER - POCSAG / FLEX
 |
The
PSR3000 Serial Receiver is a powerful PDR type paging
receiver/decoder with single serial data or TTL output. It
incorporates an M16 processor which significant amount of data
processing capability.
The PSR3000 provides a relay output
and up to 3 digital control outputs or to be interfaced with
external Relay Control Board for multiple relay outputs.
- Text search and
replace
- Inbuilt
pocsag encoder
- VHF, UHF,
900MHz
- Pocsag and
Flex
- Serial data
port
- External
antenna on BNC connector
|
|
|
|
TMR1 SERIAL RECEIVER - POCSAG / FLEX
.jpg) |
The
TMR1 Telemetry Messaging Receiver is a one way Paging device with
output ports which is used as a low cost device to receive wireless
data or control equipment. Each output can be turned ON and OFF with
separate message. All 8 ports can be controlled with one message
- POCSAG or FLEX
- VHF / UHF
- 7 Capcode
- Modular or in
robust case
- Various
Antenna output
Some of the applications are;
- Irrigation
- Lighting
- Traffic
Signals & Signs
- Traffic
Warning Systems
- Vending
Machines
- LED Displays
- Utility
Control
- Vehicle
Function Control
|
PDR3000
Paging Data receiver
 |
The
PDR3000 Paging Data Receiver is a multi-function paging data
receiver, off air decoder capable of receiving pager messages and
processing them in a variety of ways. It is able to print messages
direct to a parallel or serial printer or output the message data
via the two serial ports in a number of different formats and
protocols. The PDR3000 may also be fitted with up to four relay
control outputs internally or may interface with the RCM2000 Relay
Control Module for Multiple relay control.
- POCSAG or FLEX
- VHF, UHF, 900
MHz
- Large Cap Codes
72000
- Serial Data
Port
- Parallel
Printer Output
- Relay Output
- Text to Voice
- Off Air
Decoder
- Relay Control
- LED Sign
Control
|
12-84SE Relay Output Pocsag Receiver
|

|
The 12-84SE VHF/UHF Relay Receiver provides the capability of remote
activation or deactivation of one or two relays on receipt of
commands from any POCSAG paging transmitter. The receiver is
supplied with two clean contact relays.
The 12-84SE receives and decodes a numeric or alphanumeric message. Relays
can be activated by message or cap code.
12-84SE is an economical solution for basic remote control
applications where one or two switched outputs are required. On
board LEDs indicate receiver operation as well as the relay status.
Each relay can be programmed for latching or momentary operation.
|
12-32
expansion module
|
 |
The 12-32 is a 32
input expansion module that may be used either autonomously with
a serial to ethernet converter or with 12-62 transmitters.
Input modules may be daisy chained together to provide as many
inputs as required.
The 12-32 supports
multiple message queuing, and will queue at least 50 character
messages, or many more smaller messages that will fit into the
available memory buffer (up to approximately 120 messages).
Pre-defined input messages are limited to a maximum length of 40
characters which may be configured with programming software. |

 
© 1997 UNICOM Pty. Ltd.
All Rights Reserved
See
Copyright
Page for Technical Specifications Disclaimer
|
|
|
|